Search the MPC:

		You are here: Home '64-'72 Ford Truck MPC SECTION 35 Page 15	[668]
		Other pages in this section: - 01 - 02 - 03 - 04 - 05 - 06 - 07 - 08 - 09 - 10 - 11 - 12 - 13 - 14 - 15 - 16 - 17 - 18 - 19 - 20 - 21 - 22 - 23 - 24 - 25 - 26 - 27 - 28 - 29 - 30 - 31 - 32 - 33 - 34

SECTION 35

YEAR	MODEL	DESCRIPTION	QTY.	PART NUMBER
3A525 — COUPLING - STEERING GEAR INPUT SHAFT TO STEERING COLUMN SHAFT
65/66	F100/250 (4x2) "Before Ser. 900,001"	Larger pin has .41" O.D. - use w/ C5TZ 3524-F	1	C5TZ 3A525-A
65/66	F100/250 (4x2) "From Ser. 900, 001"	Larger pin has .56" O.D.	1	C6TZ 3A525-A
67/68 69	F100/350 (4x2) E100/300 " Before Ser. D68,001"	Has (1) large & (1) small pin - w/o locators	1 1	C6TZ 3A525-A
69/	E100/300 "From Ser. D68,001"	Includes (2) 382634-S100 nut	1	C9UZ 3A525-A
69/	F100/250 (4x2), F350	r/b D3TZ 3A525-A	1	C9TZ 3A525-B
67/	B-F500/750 - P/S	5M, 5.5M, 6M, 7M, 9M front axles	1	C8TZ 3A525-A
67/	B-F600/750	Bolt (to steering gear) - 3/8"-24 x 1.22"	1	358794-S (BB815AB)
69/ 70/	F100/250 (4x2), F350, E100/300 B-F500/750	Nut (flange to column assy.) - 5/16"-18	2 2	382634-S100 (MM173NE)

YEAR	MODEL	DESCRIPTION	QTY.	PART NUMBER
3D525 — BEARING - P/S GEAR INPUT SHAFT - Refer to Steering Gear Parts Lists Section 35.1
		Straight roller type - 7/8" I.D. x 1 1/8" O.D. x 3/8" thick	1	C6TZ 3D525-A
		Needle or ball brg. - std. - 1.501" O.D.	1	C5AZ 3D525-A
		Ball brg. - O/S - black oxide on outer race -1.505" O.D. - #DD43007	1	C5AZ 3D525-C

YEAR	MODEL	DESCRIPTION	QTY.	PART NUMBER
3D525 — BEARING - P/S PUMP ROTOR SHAFT - Refer to P/S Pump Section 36.1
		Ball type - 21/32" I.D. x 1 9/16" O.D. x 15/32" thick		C6TZ 3D525-B

YEAR	MODEL	DESCRIPTION	QTY.	PART NUMBER
3F525 — BRACKET - P/S RESERVOIR OIL FILLER TUBE
70/	L-LN-LNT-LT-LTS (Detroit I-6 Diesel)	Pump reservoir filler tube bracket - improvise	1	D0HA 3F525-A
		Bolt - 3/8"-16 x 1" (bracket to engine)	2	58634-S
		Washer - 3/8" - flat	4	351385 -S (XX158)
		Nut - 3/8"-16	2	34987-S

YEAR	MODEL	DESCRIPTION	QTY.	PART NUMBER
3A526 — SHAFT ASSY. - STEERING COLUMN

B SERIES
67/70	B500/750 - Manual steering	5/8"-18 x 39 1/2" - includes C3TZ 3D510-A, C3TZ 3507-B, C7TZ 3A527-B, C6TZ 3A528-A & C6TZ 3A529-A - NOTE 2	1	C7TZ 3A526-B
	B500/750 - Manual steering	41 1/8" long - NOTE 1	1	C9TZ 3A526-D
	B500/750 - P/S	Shaft & flange - 36 3/8" long	1	C7TZ 3524-B
71/	B500/750 - M/S	#D1TA 3A526-BB - includes 3507 clamp, 3D510 boot, 3A527 shaft, 3A528 shell, 3A529 buttons	1	D1TZ 3A526-B
71/	B500/750 - P/S	36 3/8" long - #D1TA 3460-CA	1	D1TZ 3524-E

C-CT SERIES
64/65 66/69 66/69 70/ 70/	C-CT550/1100 C800, (C850 exc. 175" W/B) - M/S C850 (175" W/B), C950/1000, CT750/950 - M/S & P/S C800/900 (9 1/2" frame) - M/S C800/900 (9 3/4" frame), CT800/900	Shaft & yoke assy. less u/joint 33 11/16" from hole center to end (use w/single joint & clamp yoke) With 12M (conv.) F/A With 12M conv. front axle	1 1 1 1 1	C3TZ 3A526-D

Includes C3OZ 3C66U-A # Identification Marking

NOTE 1 - Must be used with steering gear C9TZ 3504-D (marked C9TA-D)
NOTE 2 - Must be used with steering gears C7TZ 3504-B (marked C7TA-E or C7TA-S) or C9TZ 3504-B (marked C8TA-K)

Symbol (in the text listings or exploded-view diagram) indicates part is not supplied for service due to the following:
          a. Part is superseded and replaced as indicated in the description column of text
          b. Part can be improvised as indicated in the description column of text
          c. Due to it's function there would be little or no demand

- Identifies unique Canadian part numbers and application and have been and footnoted.

- Identifies unique U.S. part numbers and application and have been footnoted.

- Site Admin notes (not part of the original MPC)