The heater-duct- flappers

Inside the cab...appearance, repair, upgrades

Moderator: FORDification

Post Reply
User avatar
jzjames
100% FORDified!
100% FORDified!
Posts: 1765
Joined: Sun Jan 09, 2005 2:59 pm
Location: Washington, Windy Point

The heater-duct- flappers

Post by jzjames »

Who’s got a suggestion for what I could use to replace the soft pads that were glued to the heater flaps?

When my heater core blew out a few years ago and I had to replace, I cleaned up the entire box. Those soft pads pretty much just brushed off of the flaps - they looked like some kind of thin foam..

Now I have pretty considerable air leakage past the flaps when theyre closed. Too hot!
Whatever goes back on has to be able to hold up to the heat.
:hmm:
User avatar
sargentrs
100% FORDified!
100% FORDified!
Posts: 9866
Joined: Fri Jun 22, 2007 9:30 am
Location: Georgia, Jasper

Re: The heater-duct- flappers

Post by sargentrs »

Factory heater replacement foam kits should still be available from LMC or DC. However, when I rebuilt my factory A/C, foam kits were not available for it. I used Armaflex adhesive backed strip from Home Depot. It's in the HVAC section. Heat and moisture resistant and soft enough to make a good seal. You can see it applied half way down page 3 and on page 4 on my A/C rebuild thread. http://www.fordification.com/forum/view ... 3&start=30 Here it is on the HD website. https://www.homedepot.com/p/Armacell-2- ... /100539553
Randy
1970 F100 Sport Custom Limited LWB, 302cid, 3 on the tree. NO A/C, NO P/S, NO P/B. Currently in 1000 pcs while rebuilding. Project thread: http://www.fordification.com/forum/view ... 22&t=59995 Plan: 351w, C4, LSD, pwr front disc, p/s, a/c, bucket seats, new interior and paint.
1987 F-150 XLT Lariat, 5.0/C6 auto.
User avatar
jzjames
100% FORDified!
100% FORDified!
Posts: 1765
Joined: Sun Jan 09, 2005 2:59 pm
Location: Washington, Windy Point

Re: The heater-duct- flappers

Post by jzjames »

Armaflex. Check. :thup:
Writing it down in my Ford folder til I can get to this project. Wonder if I’ll have to disassemble alot.
390FE1972
Blue Oval Fan
Blue Oval Fan
Posts: 561
Joined: Tue Jul 15, 2014 10:28 pm
Location: Colorado Springs, CO

Re: The heater-duct- flappers

Post by 390FE1972 »

You have to take the back metal plate off to get to the flappers, which requires removing the rivets that hold the front "plastic" and the back metal piece together. I did a complete rebuild on mine using the Dennis Carpenter rebuild kit, in my opinion you might as well do it all right all at once. I used small machine screws and nuts to replace the rivets. Here is Randy's excellent thread on rebuilding the heater box, and the link to the DC rebuild kit:

http://www.fordification.com/forum/view ... =6&t=73960
https://www.dennis-carpenter.com/trucks ... -fresh-air

Regards :thup:
1972 F250 Sports Custom 390 FE C6 2WD Dana 60 4:10 gears
User avatar
sargentrs
100% FORDified!
100% FORDified!
Posts: 9866
Joined: Fri Jun 22, 2007 9:30 am
Location: Georgia, Jasper

Re: The heater-duct- flappers

Post by sargentrs »

Thanks 390FE1972! I'd forgotten about that :lol:
Randy
1970 F100 Sport Custom Limited LWB, 302cid, 3 on the tree. NO A/C, NO P/S, NO P/B. Currently in 1000 pcs while rebuilding. Project thread: http://www.fordification.com/forum/view ... 22&t=59995 Plan: 351w, C4, LSD, pwr front disc, p/s, a/c, bucket seats, new interior and paint.
1987 F-150 XLT Lariat, 5.0/C6 auto.
User avatar
jzjames
100% FORDified!
100% FORDified!
Posts: 1765
Joined: Sun Jan 09, 2005 2:59 pm
Location: Washington, Windy Point

Re: The heater-duct- flappers

Post by jzjames »

Thanks for the help.
I should have done the full rebuild when I had it out for the heater core. :doh:
User avatar
basketcase0302
100% FORDified!
100% FORDified!
Posts: 6805
Joined: Thu Jan 26, 2006 7:11 am
Location: Hawthorne, Florida

Re: The heater-duct- flappers

Post by basketcase0302 »

I used a thin rubber type insulation like Armaflex when i did my complete rebuild but can't remember the source of if it was something Zi had laying around? :hmm:
Jeff
http://www.fordification.com/forum/view ... 22&t=46251
SOLD-71 F-350 dually flatbed, 302 / .030 over V-8 with a "baby"C-6, B & M truckshifter, Dana70/4.11 ratio, intermittent wipers, tilt steering, full LED lighting on the flat bed, and no stereo yet (this way I can hear the rattles to diagnose)! SOLD!
Many Ford bumps / one 76' EB / and several dents through the years.
A lot of "oddball" Ford parts collected from working on them for 34 years now!
2008 Ford Escape 4 x 4
Post Reply