What trans adaptor for a 4r70w with 351c

Clutch, transmission, rear axle

Moderators: FORDification, 70_F100

Post Reply
Mercury100
New Member
New Member
Posts: 49
Joined: Thu Oct 05, 2017 10:31 pm

What trans adaptor for a 4r70w with 351c

Post by Mercury100 »

I see lots of adapters for gm 4L80e and 4L60e and 700r4
User avatar
Manny
Blue Oval Guru
Blue Oval Guru
Posts: 1190
Joined: Wed Oct 04, 2006 7:15 pm
Location: Georgia, Lake City
Contact:

Re: What trans adaptor for a 4r70w with 351c

Post by Manny »

Mercury100 wrote:I see lots of adapters for gm 4L80e and 4L60e and 700r4

If it's a genuine cleveland. No issue the clevelands shared a 302 351 bell housing pattern. so find yourself a small block 4r70w and rock on!
Just another Ford fool named Dan.
The Junk that hangs around
67' F-250 highboy Camper special cross breed currently under way
http://www.fordification.com/forum/view ... 22&t=86706
1974 Bronco 302 3 speed
1984 bronco 302 c6 35's
1994 F350 7.3 5spd dually.
woods wrote: The rust holes in my truck were a factory install (very rare).
Mercury100
New Member
New Member
Posts: 49
Joined: Thu Oct 05, 2017 10:31 pm

Re: What trans adaptor for a 4r70w with 351c

Post by Mercury100 »

The Older ford small block bolt pattern is not the same as the newer modular engine bolt pattern.
I could be wrong. Some one correct me if I’m wrong.
User avatar
Manny
Blue Oval Guru
Blue Oval Guru
Posts: 1190
Joined: Wed Oct 04, 2006 7:15 pm
Location: Georgia, Lake City
Contact:

Re: What trans adaptor for a 4r70w with 351c

Post by Manny »

Mercury100 wrote:The Older ford small block bolt pattern is not the same as the newer modular engine bolt pattern.
I could be wrong. Some one correct me if I’m wrong.
I may be wrong not mod motor special I will check this. I am putting 4r75W guts in a AOD case to keep full hydraulic drive style.
Just another Ford fool named Dan.
The Junk that hangs around
67' F-250 highboy Camper special cross breed currently under way
http://www.fordification.com/forum/view ... 22&t=86706
1974 Bronco 302 3 speed
1984 bronco 302 c6 35's
1994 F350 7.3 5spd dually.
woods wrote: The rust holes in my truck were a factory install (very rare).
JoshT
Preferred User
Preferred User
Posts: 327
Joined: Sat Oct 10, 2015 11:09 pm
Location: Middle Georgia

Re: What trans adaptor for a 4r70w with 351c

Post by JoshT »

Mercury100 wrote:The Older ford small block bolt pattern is not the same as the newer modular engine bolt pattern.
I could be wrong. Some one correct me if I’m wrong.
4R70W was installed with the 302 in the V8 Explorers. 302 Windsor has the same bolt pattern as all the other older ford small blocks. Yes, I'm sure about this because I have a 98 Explorer 302 and 4R70W sitting on a 86 Ranger frame in the back yard.
1968 F-100 4x4 long bed - 360 FE - NP435 w/ Dana 21 - PS & PB conversion - Front Disc Swap - 265/75R16 - 1" S.L. & 2" B.L. (to be removed) - Homemade tube bumpers - Warn 8274 - Currently wearing 1970 body
Mercury100
New Member
New Member
Posts: 49
Joined: Thu Oct 05, 2017 10:31 pm

Re: What trans adaptor for a 4r70w with 351c

Post by Mercury100 »

Thanks for the info.
Post Reply