1971 F250 Camper Special with 429 swap and no power

Engine, ignition, fuel, cooling, exhaust

Moderators: Ranchero50, DuckRyder

Post Reply
multiphonic
New Member
New Member
Posts: 3
Joined: Mon May 25, 2015 11:29 pm

1971 F250 Camper Special with 429 swap and no power

Post by multiphonic »

Hi all,
I have had my Camper Special for a few years now and have been struggling with it making enough power to go freeway speeds over the pass with a camper on the back. Is this normal?
I bought it with the 429 already in it (previous owner said it was from an early 70's Thunderbird) and after a new Edelbrock carb, new fuel, oil, water pump, timing chain and HEI distributor it seems to run great. compression test shows around 90 for each cylinder and cruising up to around 45 or 50 it runs like a dream. Going up steep mountain passes it turns completely gutless and heat goes way up (water temp around 270) and can only do about 35. Also when I push it on the flats, anything 60 and above it makes the belts squeal. No matter what belt or how tight or loose I make them, they squeal. Tried multiple brands and it makes no difference.
Seems strange for such a big engine but I don't know what normal is.
Any advice or experience? Should I not expect much more with a fully loaded camper on the back?
Thanks.
1971 F250 Camper Special Ranger XLT
User avatar
Ranchero50
Moderator
Moderator
Posts: 5799
Joined: Wed Nov 08, 2006 7:02 pm
Location: Maryland, Hagerstown
Contact:

Re: 1971 F250 Camper Special with 429 swap and no power

Post by Ranchero50 »

90 psi ???

I'd pull it apart and find out what you have and build it to what you need. Sounds like cam timing is off or it has really low compression. Not a happy engine.
'70 F-350 CS Cummins 6BT 10klb truck 64k mile Bahama Blue

Contact me for CNC Dome Lamp Bezels and Ash Tray pulls.
multiphonic
New Member
New Member
Posts: 3
Joined: Mon May 25, 2015 11:29 pm

Re: 1971 F250 Camper Special with 429 swap and no power

Post by multiphonic »

Yes 90 psi... From what I was reading, that isn't too bad as long as all the cylinders are the same-ish. What is normal compression for these engines?
1971 F250 Camper Special Ranger XLT
tnlprt
Blue Oval Guru
Blue Oval Guru
Posts: 1144
Joined: Thu Jul 08, 2010 5:18 pm
Location: St Louis mo

Re: 1971 F250 Camper Special with 429 swap and no power

Post by tnlprt »

I would verify the ignition timing

I would also swap out the timing chain and gears for a set for a 1968 to insure it does not have the late model set which retards the cam
Beardlife
New Member
New Member
Posts: 13
Joined: Wed Jul 19, 2017 9:13 am
Location: Central Coast, California

Re: 1971 F250 Camper Special with 429 swap and no power

Post by Beardlife »

90 seems low to me too. Think about barometric pressure wherever you are, and multiply that by your compression ratio. I'm close to sea level (14.7) and my 71 360 makes 120-125 psi (about 8.5 to 1). You might also check your ignition total advance, as I recall a retarded spark will run hotter. Under load like you're describing, you should be losing some vacuum advance.
1971 F250 360 C6
The wise man builds himself, the fool waits only to die.
User avatar
bluef250
Blue Oval Fanatic
Blue Oval Fanatic
Posts: 924
Joined: Fri Oct 29, 2004 8:49 pm
Location: Arizona

Re: 1971 F250 Camper Special with 429 swap and no power

Post by bluef250 »

i would expect compression at 120 - 140 psi

The cam's in the late 1960's were the weak link in the 429 - 460 engines. So you might start trouble shooting with the cam.
Post Reply